BEEKEEPING LEARNING CENTER > DOWN UNDER BEEKEEPING
Homemade Screened Bottom Board Construction Technique
Lesgold:
Hi Folks,
With the arrival of Varroa, our beekeeping methods are about to change forever. Many of our techniques and the equipment that we use will have to be modified to a certain extent to give us the edge over this pest. A lot of people on the forum from other parts of the world have been dealing with this issue for many years and they have developed some great ideas in their approach to managing varroa. One area that I have been looking into over the past couple of years is screened bottom boards. The experts in Australia are telling us that they play a minor role in keeping varroa levels down by allowing phoretic mites that fall from bees to pass through a screen and be collected in a tray. If these bottom boards were able to play a major part in the control of varroa, I?m sure that everyone would be using them. In reality, many beekeepers do a great job with solid boards and don?t feel there is any reason to head down that path. I get that and have no argument with what they are saying.
I?m changing to screened bottom boards because of a number of reasons that apply to the situation in my area. Varroa is getting close now and may arrive at any time. I want to be able to check hives regularly to see if mites are present but don?t want to open the hives until the weather warms up a bit. A sticky mat under a screened bottom board will be a good way to show the presence of mites and from that, alcohol wash tests could be performed. When mites hit, hive strength will be impacted significantly and this will give small hive beetles a huge advantage. The SBB tray will be used to help control beetles with either oil or diatomaceous earth. Finally, during summer months, the tray position could be changed to modify air flow into the hive.
Why make bottom boards when you can buy them already assembled? There are many reasons for this. The first reason is ?because I can?. I have a bit of workshop equipment, the time to dedicate to the task and always enjoy building stuff. The second reason is cost. Quite a bit of money can be saved by constructing them at home. The time used to make them is not an issue as I?m retired. Next on the list is painting. I hate painting with a passion. It bores me to tears. Painting assembled bottom boards with screens in place would be a nightmare. The other issue is that you are not going to be able to get paint under the risers which will cause rot issues down the track. Store purchased BB?s are made from pine and are not going to last long in coastal areas. I have been told a couple of years is what you would expect to get. That?s just not good enough. The last reason is in relation to the trays. They are constructed from galvanised sheet. If acidic mite treatments are to be used, rust will be a real issue.
I designed and made a few variations of a SBB that have been in use for about 12 months now. They seem to be working well but there was too much time allocated to making them. The design has been simplified to make assembly easier and I plan to run you through the construction process as 10 of them are made. Hopefully it will give some of you some ideas and hopefully you can improve upon what is presented. Timber will be purchased tomorrow and we can make a start. Major dimensions, material costs and suppliers will be provided as well as a stack of photos.
Michael Bush:
Many of us went to screened bottom boards only to go back to solid. It didn't really help with the Varroa. In fact there is some research that it made things worse. The Varroa reproduce better if it's slightly cooler...
Lesgold:
Interesting comment Michael. The bottom board that I will be making doesn?t increase ventilation unless you want it to so it will be good to find out. As I said earlier, there are other reasons for using the SBB as well. It would be nice to know some detail on how they perform in different climates. I know you are a fan of solid BB?s because of how they work for you in your environment and how you manage your bees. I would love to be in your position to be treatment free but unfortunately the information coming through about hives in my temperate climate is devastating.
Lesgold:
The main materials for the bottom board are shown below. The tray was purchased from Kmart. They are 450x350mm and fit quite well into the internal space of the bottom board. There is a gap of approximately 10mm on each side so it will cover the brood area quite well. Cost is very good at $3.50 per unit. Being plastic, it won?t react with any acidic varroa treatments and will be able to hold vegetable oil or diatomaceous earth for beetle control.
I was able to find a supplier of woven stainless steel mesh. It is pre cut to 495x 400mm which works quite well for a 10 frame box. The wire is .99mm in diameter with an opening of 3.5mm which will prevent bee entry but allow varroa and beetles to fall through. I purchased a pack of 5 about a month ago to see what the quality was like and was very happy with how sturdy the mesh looked. It would have been better if it was a few mm wider but it still works. A pack of 5 cost $40 + postage. They ended up costing about $12 ea. delivered. A larger order was placed a couple of days ago and the unit price dropped to below $7 (including delivery). This item was purchased from The Bee Store in Melbourne.
The timber I decided to use was cypress pine. It has a high, natural oil content and will outlast most other timbers in an external environment. The only issue with it is that it doesn?t nail well and will crack if pilot holes aren?t used. I will drill and screw all major components together which removes this problem. The timber also tends to contain quite a few knots so there is time needed to select individual pieces. 65x20mm pine pickets are available from Bunnings. The timber is dressed but is not seasoned. This is not an issue as it is quite stable and when assembled and does not move. 900mm pickets are a convenient size and offer the best value for money. 3 pickets will be needed for each bottom board. Cost per item is $3.80.
Risers will be made from Weathertex. It lasts extremely well and is easy to machine and paint. Many hardware stores sell this material as do beekeeping suppliers. I was able to pick up a packing sheet that was damaged for $2 from a hardware store.
Most components will be held in place with galvanised screws. Stainless would be a better option but I decided to keep costs down. Most screws will be covered in paint or concealed from the environment so they should last quite well. 8-10# countersunk 25mm and 40mm screws will be used for the project. They were purchased from Bunnings at around $10 per pack of 100. A few other minor components will be needed for the project and will be spoken about at the appropriate time.
The equipment used for construction of these bottom boards include a drop saw, saw bench, portable power saw, drill press, cordless drill and a narrow crown stapler. Many people won?t have access to much of this equipment and I will describe alternatives as the construction phase takes place. It is possible to make this project using just a cordless or even a corded driver drill and a portable power saw. For those people who don?t feel comfortable using a power saw, a jig saw could be used in its place. These options would just slow the process as a few jigs would be needed to safely hold material during the cutting process.
Lesgold:
The first step is to mark out and cut the long sides of the bottom board. In this design, I won?t be including a landing board as I don?t believe it is essential. I have a number of bottom boards that finish flush with the end of the brood box and the bees don?t have any issues with it. For those who want one, you can add it after the BB is assembled. It just makes extra work and increases the cost slightly. Australian 10 frame boxes are 508mm long so a stop is set exactly to that distance and multiple cuts are made while the drop saw is set up. If you are using a jig saw or a portable power saw, individual pieces could be marked out and cut or a simple jig could be made to ensure each piece is cut square and exactly to length.
Standard 10 frame boxes are 406mm wide so the length required is calculated and one piece is prepared and the width dimension is checked before the drop saw is set to cut remaining pieces. Please remember that dimensions given when purchasing timber are rarely accurate and adjustments will have to be made.
The last photograph shows the material cut for 10 bottom boards and the small amount of waste produced. This should take about 15 minutes if you take your time and double check measurements. Using a jig saw or portable power saw will just increase the time. It?s better to be accurate than to rush.
Navigation
[0] Message Index
[#] Next page
Go to full version