Author Topic: Coates 5-Frame Nuc (Read 114862 times)

Meadlover · « **Reply #20 on:** August 26, 2010, 11:47:03 pm »

This is a great design for a nuc.
I make a couple a few weeks back, and if I can find some cheap ply I'll be making a hep more for swarm season!
Thanks again for this thread and the photos D Coates :lol:

ML

Tommyt · « **Reply #21 on:** August 27, 2010, 11:49:19 am »

This is a great design
I'll be making a sheet of them this weekend
Thanks for Posting
I vote this too be a Sticky
Tommyt

ronwhite3030 · « **Reply #22 on:** August 27, 2010, 12:35:48 pm »

sticky this

D Coates · « **Reply #23 on:** August 30, 2010, 10:42:55 am »

Quote from: ronwhite3030 on August 25, 2010, 01:20:19 pm

what size wire did you use for the feeder hole?

8?, whatever size is normally used for SBB's. Invariably there's scrap wire left over from making SBB's this is where I use some of that.

charmd2 · « **Reply #24 on:** September 11, 2010, 03:00:17 pm »

a bump back to the top as this has been a wonderful wonderful wonderful post to me. :)

The Bix · « **Reply #25 on:** January 07, 2011, 09:54:01 pm »

Uploaded with ImageShack.us

WOW! That was easy, bring on swarm season! Thanks for the plans D Coates!

hareman · « **Reply #26 on:** January 10, 2011, 07:40:08 pm »

Hey D Coates! Thanks for the great plans for the nuc/swarm catcher box! I actually made eight of them last Friday. I accidently bought a sheet of 3/8 (11/32") plywood and cut everything out - then realized my mistake. I had a few pieces of scrap 15/32" plywood laying around so I made the end pieces out of these, used the 3/8" sides, bottom, and top pieces and the frames fit perfectly! I still had half a day left and I was so inspired and pleased with my four 'mistake boxes' that I went back to Lowes and bought a sheet of 15/32" and made four more boxes in just under three hours. Not a bad day's work (or fun) and I now have eight swarm traps ready for painting for a total expense of less than $40.00, including glue and brads. I used 1-1/4" brads and my brad nailer to hold stuff together while the Titebond III glue dried. I have some medium brown Behr exterior latex enamel left over from another job that I intend to use on them before putting them out. Your measurements were "Dead On" and no adjustments were necessary when assembling them.
Thanks again for sharing.

Mtn. Bee · « **Reply #27 on:** January 10, 2011, 07:55:51 pm »

Thanks for sharing, excellent plans! :-D :-D

VolunteerK9 · « **Reply #28 on:** January 10, 2011, 10:43:08 pm »

Quote from: The Bix on January 07, 2011, 09:54:01 pm

Uploaded with ImageShack.us

WOW! That was easy, bring on swarm season! Thanks for the plans D Coates!

Hey Bix..were these some of your driveway builds? :-D

Looks good

shorty3 · « **Reply #29 on:** January 10, 2011, 10:44:53 pm »

thanks this is something i have been trying to find for a long time. i have some scraps that i have been letting pile up

The Bix · « **Reply #30 on:** January 10, 2011, 11:35:22 pm »

Hey Bix..were these some of your driveway builds? :-D

Looks good
[/quote]

Exactly :) though I did sneak a two or three cuts inside the garage. SShhhhh!

Tommyt · « **Reply #31 on:** January 27, 2011, 01:50:37 am »

Swarms are coming down south soon
I should have had 10 of these built all ready
But as usual I dragged azz :-x
Does anyone have the layout drawing for a 4x8
piece of ply wood I thought it was posted
and I had it saved :?

Tommyt

Robo · « **Reply #32 on:** January 27, 2011, 10:12:03 am »

Quote from: Tommyt on January 27, 2011, 01:50:37 am

Swarms are coming down south soon
I should have had 10 of these built all ready
But as usual I dragged azz :-x
Does anyone have the layout drawing for a 4x8
piece of ply wood I thought it was posted
and I had it saved :?

Tommyt

Tommy,

If your looking for swarm traps, I do have a layout drawing for my $2 swarm trap that get 15 traps out of 2 sheets of ply, 1/2 sheet luan, and some coroplast signs.

BTW, I think Drew has a great design on these nucs, and sent him PM to see if he would be OK with me putting plans and layout drawing for his nuc on my website (with full credit to him of course). If I get his permission, I'll put it out for download tonight.

Tommyt · « **Reply #33 on:** January 28, 2011, 12:12:52 pm »

Robo
PM sent
thanks
Tommy

Robo · « **Reply #34 on:** January 28, 2011, 02:36:19 pm »

Quote from: Robo on January 27, 2011, 10:12:03 am

BTW, I think Drew has a great design on these nucs, and sent him PM to see if he would be OK with me putting plans and layout drawing for his nuc on my website (with full credit to him of course).

Plans can be found here -> http://robo.bushkillfarms.com/beekeeping/downloads/

KD4MOJ · « **Reply #35 on:** January 28, 2011, 03:29:29 pm »

WOW! Robo you do the drawing or Drew? Whichever thanks!!!!!!!!!!!

...DOUG
KD4MOJ

Robo · « **Reply #36 on:** January 28, 2011, 05:05:23 pm »

I drew them, but Drew did the thinking ;)

AllenF · « **Reply #37 on:** January 28, 2011, 08:55:53 pm »

They look good there.

Tommyt · « **Reply #38 on:** January 28, 2011, 11:44:49 pm »

Here is the drawing I was looking for on D Coates

Robo · « **Reply #39 on:** January 29, 2011, 08:13:19 am »

Tommy,

Be careful with that layout, it doesn't account for the saw kerf. So although it appears that there is some scrap from the initial rip cuts, assuming 1/8" kerf, there is less than 1/10" of an inch. In fact, if you look at the measurements, they already reduced the width of the end caps 1/8" to make it fit.

If you prefer rip cuts, here is a layout that gives you a little margin with full width end caps.

I included the layout for preferred cross cuts with the plans.