Welcome, Guest

Author Topic: Coates 5-Frame Nuc  (Read 113412 times)

Offline Meadlover

  • House Bee
  • **
  • Posts: 216
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #20 on: August 26, 2010, 11:47:03 pm »
This is a great design for a nuc.
I make a couple a few weeks back, and if I can find some cheap ply I'll be making a hep more for swarm season!
Thanks again for this thread and the photos D Coates  :lol:

ML

Offline Tommyt

  • Field Bee
  • ***
  • Posts: 855
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #21 on: August 27, 2010, 11:49:19 am »
This is a great design
I'll be making a sheet of them this weekend
Thanks for Posting
I vote this too be a Sticky
Tommyt
"Not everything found on the internet is accurate"
Abraham Lincoln

Offline ronwhite3030

  • House Bee
  • **
  • Posts: 218
Re: Simple 5 frame nuc plans
« Reply #22 on: August 27, 2010, 12:35:48 pm »
sticky this

Offline D Coates

  • Queen Bee
  • ****
  • Posts: 1231
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #23 on: August 30, 2010, 10:42:55 am »
what size wire did you use for the feeder hole?

8?, whatever size is normally used for SBB's.  Invariably there's scrap wire left over from making SBB's this is where I use some of that.
Ninja, is not in the dictionary.  Well played Ninja's, well played...

Offline charmd2

  • House Bee
  • **
  • Posts: 127
  • Gender: Female
Re: Simple 5 frame nuc plans
« Reply #24 on: September 11, 2010, 03:00:17 pm »
a bump back to the top as this has been a wonderful wonderful wonderful post to me. :) 
Charla Hinkle

Offline The Bix

  • House Bee
  • **
  • Posts: 427
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #25 on: January 07, 2011, 09:54:01 pm »


Uploaded with ImageShack.us

WOW!  That was easy, bring on swarm season!  Thanks for the plans D Coates!

Offline hareman

  • New Bee
  • *
  • Posts: 21
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #26 on: January 10, 2011, 07:40:08 pm »
Hey D Coates! Thanks for the great plans for the nuc/swarm catcher box! I actually made eight of them last Friday. I accidently bought a sheet of 3/8 (11/32") plywood and cut everything out - then realized my mistake. I had a few pieces of scrap 15/32" plywood laying around so I made the end pieces out of these, used the 3/8" sides, bottom, and top pieces and the frames fit perfectly! I still had half a day left and I was so inspired and pleased with my four 'mistake boxes' that I went back to Lowes and bought a sheet of 15/32" and made four more boxes in just under three hours. Not a bad day's work (or fun) and I now have eight swarm traps ready for painting for a total expense of less than $40.00, including glue and brads. I used 1-1/4" brads and my brad nailer to hold stuff together while the Titebond III glue dried. I have some medium brown Behr exterior latex enamel left over from another job that I intend to use on them before putting them out. Your measurements were "Dead On" and no adjustments were necessary when assembling them.
Thanks again for sharing.
Do your best and let God do the rest.

Offline Mtn. Bee

  • New Bee
  • *
  • Posts: 6
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #27 on: January 10, 2011, 07:55:51 pm »
Thanks for sharing, excellent plans!    :-D :-D
Hugus Creek Honey Farm
"Like us on Facebook"

Offline VolunteerK9

  • Super Bee
  • *****
  • Posts: 1647
  • Gender: Male
  • Gamecock fan in UT land.
Re: Simple 5 frame nuc plans
« Reply #28 on: January 10, 2011, 10:43:08 pm »


Uploaded with ImageShack.us

WOW!  That was easy, bring on swarm season!  Thanks for the plans D Coates!

Hey Bix..were these some of your driveway builds?  :-D

Looks good

Offline shorty3

  • New Bee
  • *
  • Posts: 19
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #29 on: January 10, 2011, 10:44:53 pm »
thanks this is something i have been trying to find for a long time. i have some scraps that i have been letting pile up

Offline The Bix

  • House Bee
  • **
  • Posts: 427
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #30 on: January 10, 2011, 11:35:22 pm »


Hey Bix..were these some of your driveway builds?  :-D

Looks good
[/quote]

Exactly :) though I did sneak a two or three cuts inside the garage.  SShhhhh!

Offline Tommyt

  • Field Bee
  • ***
  • Posts: 855
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #31 on: January 27, 2011, 01:50:37 am »
Swarms are coming down south soon
I should have had 10 of these built all ready
But as usual I dragged azz :-x
Does anyone have the layout drawing for a 4x8
piece of ply wood I thought it was posted
and I had it saved  :?

Tommyt
« Last Edit: January 27, 2011, 02:17:53 am by Tommyt »
"Not everything found on the internet is accurate"
Abraham Lincoln

Offline Robo

  • Technical
  • Administrator
  • Galactic Bee
  • *******
  • Posts: 6778
  • Gender: Male
  • Beekeep On!
    • Bushkill Bee Vac
Re: Simple 5 frame nuc plans
« Reply #32 on: January 27, 2011, 10:12:03 am »
Swarms are coming down south soon
I should have had 10 of these built all ready
But as usual I dragged azz :-x
Does anyone have the layout drawing for a 4x8
piece of ply wood I thought it was posted
and I had it saved  :?

Tommyt

Tommy,

If your looking for swarm traps, I do have a layout drawing for my $2 swarm trap that get 15 traps out of 2 sheets of ply, 1/2 sheet luan, and some coroplast signs.


BTW, I think Drew has a great design on these nucs, and sent him PM to see if he would be OK with me putting plans and layout drawing for his nuc on my website (with full credit to him of course).  If I get his permission,  I'll put it out for download tonight.



"Opportunity is missed by most people because it comes dressed in overalls and looks like work." - Thomas Edison



Offline Tommyt

  • Field Bee
  • ***
  • Posts: 855
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #33 on: January 28, 2011, 12:12:52 pm »
Robo
 PM sent
thanks
Tommy
"Not everything found on the internet is accurate"
Abraham Lincoln

Offline Robo

  • Technical
  • Administrator
  • Galactic Bee
  • *******
  • Posts: 6778
  • Gender: Male
  • Beekeep On!
    • Bushkill Bee Vac
Re: Simple 5 frame nuc plans
« Reply #34 on: January 28, 2011, 02:36:19 pm »
BTW, I think Drew has a great design on these nucs, and sent him PM to see if he would be OK with me putting plans and layout drawing for his nuc on my website (with full credit to him of course). 

Plans can be found here -> http://robo.bushkillfarms.com/beekeeping/downloads/
"Opportunity is missed by most people because it comes dressed in overalls and looks like work." - Thomas Edison



Offline KD4MOJ

  • Field Bee
  • ***
  • Posts: 719
  • Gender: Male
  • Bees... Motorcycles... amateur radio...
    • TangleWood Apiary
Re: Simple 5 frame nuc plans
« Reply #35 on: January 28, 2011, 03:29:29 pm »
WOW!  Robo you do the drawing or Drew? Whichever thanks!!!!!!!!!!!

...DOUG
KD4MOJ

Offline Robo

  • Technical
  • Administrator
  • Galactic Bee
  • *******
  • Posts: 6778
  • Gender: Male
  • Beekeep On!
    • Bushkill Bee Vac
Re: Simple 5 frame nuc plans
« Reply #36 on: January 28, 2011, 05:05:23 pm »
I drew them, but Drew did the thinking ;)
"Opportunity is missed by most people because it comes dressed in overalls and looks like work." - Thomas Edison



Offline AllenF

  • Galactic Bee
  • ******
  • Posts: 8192
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #37 on: January 28, 2011, 08:55:53 pm »
They look good there.

Offline Tommyt

  • Field Bee
  • ***
  • Posts: 855
  • Gender: Male
Re: Simple 5 frame nuc plans
« Reply #38 on: January 28, 2011, 11:44:49 pm »
Here is the drawing I was looking for on D Coates


"Not everything found on the internet is accurate"
Abraham Lincoln

Offline Robo

  • Technical
  • Administrator
  • Galactic Bee
  • *******
  • Posts: 6778
  • Gender: Male
  • Beekeep On!
    • Bushkill Bee Vac
Re: Simple 5 frame nuc plans
« Reply #39 on: January 29, 2011, 08:13:19 am »
Tommy,


Be careful with that layout,  it doesn't account for the saw kerf.  So although it appears that there is some scrap from the initial rip cuts,  assuming 1/8" kerf, there is less than 1/10" of an inch.   In fact, if you look at the measurements, they already reduced the width of the end caps 1/8" to make it fit.

If you prefer rip cuts,  here is a layout that gives you a little margin with full width end caps.



I included the layout for preferred cross cuts with the plans.
"Opportunity is missed by most people because it comes dressed in overalls and looks like work." - Thomas Edison



 

anything